True to life color
High Definition
Optical Glass
Ultra Slim Frame
Waterproof and Pro Nano Coating
ND64 6 Stop
The NiSi HUC IR Neutral Density Filter ND64 (1.8) 6 Stop is specially designed to reduce the amount of light entering the camera by 6 stops. This filter is made from high-quality optical glass with nano coating to prevent losing any single bit of detail. Neutral density filters do not affect the coloration of the image and the 1.8 density provides a 6 stop reduction in light from entering the lens.

The ND Filter creates a darkening of the entire image, allowing you to photograph with a wider aperture or slower shutter speed than normally required. By slowing your exposure time or increasing your aperture, you are able to control the depth of field and convey movement in your images. The ND64 6 stops ND filter is generally used during the golden hour to create exposures of 1-2 minutes for smooth water or clouds. A 6 Stop is also great for capturing dynamic water while retaining some texture before the golden hour.

By using neutral density filters the camera is vulnerable to infrared light which will cast the unwanted red color to the photos when shooting at a small aperture. The added infrared protection coating layer to this filter helps to eliminate the infrared light through the lens to bring back the natural color.

True to life color
High Definition
Optical Glass
Ultra Slim Frame
Waterproof and Pro Nano Coating
ND64 6 Stop
The NiSi HUC IR Neutral Density Filter ND64 (1.8) 6 Stop is specially designed to reduce the amount of light entering the camera by 6 stops. This filter is made from high-quality optical glass with nano coating to prevent losing any single bit of detail. Neutral density filters do not affect the coloration of the image and the 1.8 density provides a 6 stop reduction in light from entering the lens.

The ND Filter creates a darkening of the entire image, allowing you to photograph with a wider aperture or slower shutter speed than normally required. By slowing your exposure time or increasing your aperture, you are able to control the depth of field and convey movement in your images. The ND64 6 stops ND filter is generally used during the golden hour to create exposures of 1-2 minutes for smooth water or clouds. A 6 Stop is also great for capturing dynamic water while retaining some texture before the golden hour.

By using neutral density filters the camera is vulnerable to infrared light which will cast the unwanted red color to the photos when shooting at a small aperture. The added infrared protection coating layer to this filter helps to eliminate the infrared light through the lens to bring back the natural color.

True to life color
High Definition
Optical Glass
Ultra Slim Frame
Waterproof and Pro Nano Coating
ND64 6 Stop
The NiSi HUC IR Neutral Density Filter ND64 (1.8) 6 Stop is specially designed to reduce the amount of light entering the camera by 6 stops. This filter is made from high-quality optical glass with nano coating to prevent losing any single bit of detail. Neutral density filters do not affect the coloration of the image and the 1.8 density provides a 6 stop reduction in light from entering the lens.

The ND Filter creates a darkening of the entire image, allowing you to photograph with a wider aperture or slower shutter speed than normally required. By slowing your exposure time or increasing your aperture, you are able to control the depth of field and convey movement in your images. The ND64 6 stops ND filter is generally used during the golden hour to create exposures of 1-2 minutes for smooth water or clouds. A 6 Stop is also great for capturing dynamic water while retaining some texture before the golden hour.

By using neutral density filters the camera is vulnerable to infrared light which will cast the unwanted red color to the photos when shooting at a small aperture. The added infrared protection coating layer to this filter helps to eliminate the infrared light through the lens to bring back the natural color.

Specifications for NiSi CF1 Shutter Release Cable for Canon/Fuji Cameras - Ledning
Designed for Canon and Fuji cameras, the NiSi CF1 Shutter Release Cable is built to meet your specific needs. These lights are compatible with Canon models such as the R6, R5, RP, R, M50, 90D, 850D, and 800D with Fuji X-PRO3, XT4, 100V, XS10, XT30, XE4, XA7, GFX100S, and GFX100.

The CF1 cable is equipped with a 3.5mm jack, which can be connected to the camera. With a length of up to 1 meter, this light offers superior flexibility to bill and adapt to the situation.

The NiSi CF1 Shutter Release Cable is a lightweight and reliable mount for Canon or Fuji cameras. It's worthwhile that we give you this camera and you pay for a skull in the camera. This is very evident when you're entering your data or looking for a single camera under a taller speaker.

Whether you are a professional photographer or an obsessive hobbyist, the NiSi Shutter Release Cable CF1 will be a great product that brings photography to the next level. With compatibility and compatibility with premium Canon and Fuji models, they can look forward to precision and bill-paying accuracy everywhere.

Professional carbon fiber photography slide

The new GVM-GP-80FW is a professional carbon fiber photography slide with flywheel. It supports up to 11 pounds of load and provides 31″ travel distance. The upgraded version of fluid damping is a very practical core technology: it can run at constant speed only by hand. Even the new photographer can easily use it, and the actual picture quality is quite stable.

Key Features
11 lb Load Capacity
23" Sliding Range
Aluminum Alloy Construction
1/4"-20 and 3/8"-16 Screw Holes
Vertical, Horizontal, and 45° Shooting
Non-Slip Feet
Camera Platform Lock
Controller
Lithium-Ion Battery Pack and Charger
Carrying Bag
The 23" Professional Video Aluminum Alloy Motorized Camera Slider from GVM is a lightweight slider designed for video recording and time-lapse photography. It supports loads up to 11 lb and features 1/4"-20 and 3/8"-16 screw holes for use on the floor, on the table, or via a ball head connected to the camera. It supports vertical, horizontal, and 45° shooting. A controller, lithium-ion battery, battery charger, and carrying bag are included.

Designed for wedding/event photography, studio, and film/video recordings
You can attach the tilt head to the dolly, adjust the slide and tilt head for straight horizontal shots, and find the balance quickly with the built-in precision spirit level
Suitable for all high-performance DSLRs, mirrorless, bridge, and video cameras, and other photographic equipment
Total number of photos calculated based on the time
When using time-lapse photography, you can check the remaining number of shots
Conveyor belt
Non-slip feet
Camera platform lock

Key Features
46" Quiet Motorized Sliding Range
Supports Cameras up to 11 Pounds
Programmable Shooting Modes
Straight, Parallax, or 120° Panning
Height-Adjustable Legs
Three 1/4"-20 & 3/8"-16 Mounting Points
NP-F-Type Battery Lasts About 8 Hours
6 x Camera Control Cables Included
The 48" GVM Professional Video Aluminum Alloy Motorized Camera Slider features an 11-pound horizontal load capacity as well as a 46" slider range, but that is just the tip of its capabilities. It has an attached controller that enables you to select and control the start/stop positions of the slider along the track, as well as selecting between video and still photo mode. The aluminum rail bed features an adjustable channel that allows you to shoot straight (perpendicular to the track rails) in a parabola to keep a subject centered as the camera tracks from side to side, or it can create a 120° panoramic camera move.

The height-adjustable feet are individually adjustable up to 0.79", allowing you to set up the slider on slightly uneven or non-level terrain, while three 1/4"-20 and three 3/8"-16 threaded mounting holes enable tripod mounting. The slider is powered via a removable 4400mAh NP-F-type battery that will run the slider for about eight hours. Six different camera control cables are included allowing the slider controller to interface with most cameras.

Programmable Modes
Automatic: Allows you to set the sliding range along the slider as it cycles between the end points of the range.
Video capture: Suitable for interviews as the motor is silent.
Delay shooting: Single-frame shooting (time-lapse) with a selectable delay between 1 and 1000.
Orientation
Adjusting the channel between the support rails allows you to adjust the position of your head on the slider as it moves between the ends of the slider track. The channel can be positioned so there is no movement during the slide. You can also set it so the camera shoots in a parabola to keep the subject centered during the move, or it pans the camera up to 120° to create a panoramic shot.
Camera Compatibility
The slider includes six cables that enable the controller to interface with a variety of cameras from Canon, Sony, Nikon, Pentax, GoPro, Fuji, Panasonic, Lycra, Olympus, Samsung, and others.

Key Features
30" Quiet Motorized Sliding Range
Supports Cameras up to 11 Pounds
Programmable Shooting Modes
Straight, Parallax, or 120° Panning
Height-Adjustable Legs
Three 1/4"-20 & 3/8"-16 Mounting Points
NP-F-Type Battery Lasts About 8 Hours
6 x Camera Control Cables Included
The 32" GVM Professional Video Aluminum Alloy Motorized Camera Slider features an 11-pound horizontal load capacity as well as a 30" slider range, but that is just the tip of its capabilities. It has an attached controller that enables you to select and control the start/stop positions of the slider along the track, as well as selecting between video and still photo mode. The aluminum rail bed features an adjustable channel that allows you to shoot straight (perpendicular to the track rails) in a parabola to keep a subject centered as the camera tracks from side to side, or it can create a 120° panoramic camera move.

The height-adjustable feet are individually adjustable up to 0.79", allowing you to set up the slider on slightly uneven or non-level terrain, while three 1/4"-20 and three 3/8"-16 threaded mounting holes enable tripod mounting. The slider is powered via a removable 4400mAh NP-F-type battery that will run the slider for about eight hours. Six different camera control cables are included allowing the slider controller to interface with most cameras.

Programmable Modes
Automatic: Allows you to set the sliding range along the slider as it cycles between the end points of the range.
Video capture: Suitable for interviews as the motor is silent.
Delay shooting: Single-frame shooting (time-lapse) with a selectable delay between 1 and 1000.
Orientation
Adjusting the channel between the support rails allows you to adjust the position of your head on the slider as it moves between the ends of the slider track. The channel can be positioned so there is no movement during the slide. You can also set it so the camera shoots in a parabola to keep the subject centered during the move, or it pans the camera up to 120° to create a panoramic shot.
Camera Compatibility
The slider includes six cables that enable the controller to interface with a variety of cameras from Canon, Sony, Nikon, Pentax, GoPro, Fuji, Panasonic, Lycra, Olympus, Samsung, and others.

[Desk Mounting Stand]: You can mount the stand on the table with practical C-clamp that is up to 2.7 inch, saving much available space.
[Durable Material Made]: Clamp camera mount is made of sturdy and lightweight aluminum alloy, provides maximum stability and portable carrying.
[Applicable and Universal]: Desk clamp stand with standard 1/4 screw can be mounted for the most cameras and lights which have a 1/4? adapter, such as ring light, DSLR camera, video camera, panel light
[What you get]: an aluminum stand

[Desk Mounting Stand]: You can mount the stand on the table with practical C-clamp that is up to 2.7 inch, saving much available space.
[Adjustable Tabletop Light Stand]: Height of stand can be expanded from 12.9 inch(32.7cm) to 22 inch(56cm), support thickness from 0.6 inch(1.5cm) to 3.4 inches(8.8cm).
[Durable Material Made]: Clamp camera mount is made of sturdy and lightweight aluminum alloy, provides maximum stability and portable carrying.
[Applicable and Universal]: Desk clamp stand with standard 1/4 screw can be mounted for the most cameras and lights which have a 1/4? adapter, such as ring light, DSLR camera, video camera, panel light
[What you get]: an aluminum stand

Key Features
Wireless iOS/Android App Control
Belt Driven with Battery-Powered Motor
Manual and Looping Motorized Motion
Set A/B Points and Time-Lapse Keyframes
1 to 100% Adjustable Sliding Speed
11 lb Horizontal Payload
Ball Head Included
Six Camera Control Cables Included
1/4"-20 and 3/8"-16 Tripod Mount Threads
Up to 10 Hours of Operation Time
Instead of using a hardwired controller, the 47" Wireless Carbon Fiber Motorized Camera Slider from GVM lets you manage and control the motorized motion via an iOS/Android app from your smartphone or tablet. Set A to B travel points and keyframed time-lapse sessions over a wireless Bluetooth connection, and capture smooth and professional-looking video and images. This belt-driven slider can be used in horizontal as well as tripod-mount inclined setups, with up to 11 lb cameras supported horizontally. A ball head is included with the slider so that you can easily adjust the tilt and swivel position of your camera. A bubble level is built into the slider carriage for checking your camera's balance.

The mobile app allows you to set the sliding speed from 1 to 100%. The app has two modes: manual and automatic. In manual mode, you can just control back and forth slides from the app, and in auto mode, you can assign specific travel points and round-trip motion. For time-lapse shots, six camera control cables are included that let you connect virtually all popular cameras from Canon, Nikon, Panasonic, and Sony.

The motor is positioned on one end of the slider and features a Sony L-series battery plate. An included NP-F750 battery provides up to 10 hours of operational runtime. The slider is made with carbon fiber rails, which allow for a lighter design than aluminum rails.

Additional Features
1/4"-20 and 3/8"-16 (with bushing) camera screws on the slider carriage (a ball head is included and can be attached to these screws)
1/4"-20 and 3/8"-16 tripod mount threads on the bottom
The slider can traverse the 47" sliding range in a minimum time of 17 seconds to a maximum of 184 seconds in video mode
In time-lapse mode, the speed range is 171 seconds to 33 minutes and 45 seconds at the slowest
Companion mobile app downloadable for free for iOS and Android

Key Features
Wireless Programmable Motorized Slider
Robust 31" Portable Travel Slider
Carbon Fiber Rails
Supports up to 5.5 lb
1/4"-20 and 3/8"-16 Tripod Mounting
Hot Swappable L-Series Battery Plates
Time-Lapse and Real-Time Capture
Integrated Display on Remote Controller
The 31" GVM GT-80WD Wireless Carbon Fiber Motorized Camera Slider is a motorized slider you can program and control remotely using the included Bluetooth remote controller or a downloadable app. The motorized slider features carbon fiber rails and is belt-driven, which delivers a smooth sliding action along the 31" of slider travel. The slider carriage has a built-in bubble level, so you can check that your setup is level. Built-in feet allow you to adjust the slider's position and level. The slider has a load capacity of 5.5 lb when horizontal.

The Bluetooth controller allows you to control and program the slider to do a variety of moves. The system supports live video shooting as well as time-lapse, with multiple keyframed positions per move. The motorized slider powers from a single NP-F750 battery, allowing you to hot-swap for uninterrupted use. The two included NP-F750 type batteries will run the system for approximately 10 hours. The remote features an integrated display and during time-lapse moves can be turned off to save battery power.

Remote Controller
The wireless controller features its own internal battery and an integrated display screen that shows slider battery power remaining, remote controller battery power remaining, Bluetooth signal strength, and info on your move
The remote controller allows you to set keyframes and control the duration of the move
You can use the remote to control the slider in manual video mode, as well as in auto mode for video, auto loop, time-lapse, and panoramic stills shooting
The slider can traverse the sliding range in a minimum time of 11.4 seconds to a maximum time of 123 seconds in video mode
In time-lapse mode, the speed range is 114 seconds to 22 minutes and 30 seconds at its slowest

1/4″ and 3/8″ Screw. Motorized camera sliders with 1/4 “and 3/8” tapped holes can be mounted on a tripod or light stand to support multiple angles.

It can also be used on feet and height-adjustable floors.

Multi-target Switching

With 2 axes (horizontal, tilt, and rotation), you can easily switch shooting targets, and also make a smooth transition between these targets as the slider moves.

Multi-angle Shooting with High Load Capacity

The camera slider is compatible with light stands or camera tripods for shooting at different angles.

Moreover, it has a load capacity of up to 11 pounds, which makes horizontal and vertical shooting smoother.

Powered by AC adapter or NP F750 battery (not included). In time-lapse mode, the battery may last for nearly 10 hours
GVM 2D 2-Axis Wireless Carbon Fiber Motorized Slider

1x Motorized Slider

1 x Controller

x Battery

2 x Battery Charger

1 x Controller Connection Line

6 x Shutter Link

1 x Shutter Extension Line

1 x Carrying Bag

Key Features
Wireless Programmable 3-Axis Slider
Mobile App Control
Carbon Fiber Rails
Supports up to 11 lb
360° Pan Range
1/4"-20 and 3/8"-16 Tripod Mounting
Hot-Swappable L-Series Battery Plates
Time-Lapse and Real-Time Capture
6 x Shutter Cables Included
Integrated Display on Remote Controller
The 32" GVM 3D 3-Axis Wireless Carbon Fiber Motorized Slider with Bluetooth Remote is a 3-axis motorized slider (track slide, pan, and tilt) that you can program and control remotely using the included Bluetooth remote controller. The motorized slider features carbon fiber rails and is belt-driven, which delivers a smooth sliding action along the 31" of travel. The slider carriage has a built-in bubble level so you can check that your setup is level, and built-in independently adjustable feet allow you to adjust its position and level. An included motorized pan base mounts onto the slider carriage providing 360° of pan and tilt. The slider has a load capacity of 11 lb when horizontal.

The Bluetooth controller allows you to control and program the slider to do a variety of moves. The system supports live video shooting as well as time-lapse, with multiple keyframed positions per move. The motorized slider powers from an included AC power supply or you can use two NP-F750-type batteries for approximately 10 hours of power. You can hot-swap batteries during the slider move for increased runtime. Six included camera control cables allow the system to trigger your camera for time-lapse. The remote features an integrated display and can be turned off during time-lapse moves to preserve battery power.

Camera Control Cables
Included with the system are six shutter cables that allow limited control, such as shutter trigger, of your camera from the system. The cameras you can control include:
DC2: Nikon D7100/D7000/D5300/D5100/D5000/D3200/D3100/D610/D600/D90/DF
N3: Canon EOS 7D/5D-series/1D/6D/50D/40D/30D/20D
S2: Sony NEX-3NL/a7/a7R/a6000/a5000/a3000
L1: Panasonic DMC-FZ50K/DMC-FZ150D/DMC-FZ30K/DMC-FZ20/DMC-FZ20K/DMC-FZ20S/DMC-FZ200/LC-1/L1/L10/G10/G2/G1/GF1/GH2/GX1/G5/DIGILUX2/DIGILUX3
DC0: Nikon D850/D810/D800E/D800/D700?D300s/D200/D5/D4/D3/DF/D1/F90/F90X/F100
Remote Controller
The wireless controller features an internal battery, and an integrated display screen that shows slider battery power remaining, remote controller battery power remaining, Bluetooth signal strength, and info on your move
The remote controller allows you to set keyframes and control the duration of the move
Remote Control
You can use the remote to control the slider in manual video mode, as well as in auto mode for video, auto loop, time-lapse, and panoramic stills shooting
The slider can traverse the 31" sliding range in a minimum time of 11.4 seconds to a maximum time of 123 seconds in video mode
In time-lapse, the speed range is 114 seconds to 22 minutes, and 30 seconds at its slowest
The pan and tilt axis each features 360° of rotation

Wireless Programmable 3-Axis Slider
Mobile App Control
Carbon Fiber Rails
Supports up to 11 lb
The 32″ ?GVM 3D 3-Axis Wireless Carbon Fiber Motorized Slider with Bluetooth Remote is a 3-axis motorized slider (track slide, pan, and tilt) that you can program and control remotely using the included Bluetooth remote controller. The motorized slider features carbon fiber rails and is belt-driven, which delivers a smooth sliding action along the 31″ of travel.

The GVM 3D-80 3-Axis Wireless Carbon Fiber Motorized slider carriage has a built-in bubble level so you can check that your setup is level, and built-in independently adjustable feet allow you to adjust its position and level. An included motorized pan base mounts onto the slider carriage providing 360 ? of pan and tilt. The slider has a load capacity of 11 lb when horizontal.

GVM 3D-80 3-Axis Wireless Carbon Fiber Motorized Slider The Bluetooth controller allows you to control and program the slider to do a variety of moves. The system supports live video shooting as well as time-lapse, with multiple keyframed positions per move. The motorized slider powers from an included AC power supply or you can use two NP-F750-type batteries for approximately 10 hours of power.

You can hot-swap batteries during the slider move for increased runtime. Six included camera control cables allow the system to trigger your camera for time-lapse. The remote features an integrated display and can be turned off during time-lapse moves to preserve battery power.

Camera Control Cables
Included with the system are six shutter cables that allow limited control, such as shutter trigger, of your camera from the system. The cameras you can control include:

DC2: Nikon D7100/D7000/D5300/D5100/D5000/D3200/D3100/D610/D600/D90/DF
N3: Canon EOS 7D/5D-series/1D/6D/50D/40D/30D/20D
S2: Sony NEX-3NL/a7/a7R/a6000/a5000/a3000
L1: Panasonic DMC-FZ50K/DMC-FZ150D/DMC-FZ30K/DMC-FZ20/DMC-FZ20K/DMC-FZ20S/DMC-FZ200/LC-1/L1/L10/G10/G2/G1/GF1/GH2/GX1/G5/DIGILUX2/DIGILUX3
DC0: Nikon D850/D810/D800E/D800/D700?D300s/D200/D5/D4/D3/DF/D1/F90/F90X/F100
Remote Controller
The GVM 3D-80 3-Axis Wireless Carbon Fiber Motorized Slider wireless controller features an internal battery. And an integrated display screen that shows slider battery power remaining. Remote controller battery power remaining, Bluetooth signal strength. And also info on your move. The remote controller allows you to set keyframes and control the duration of the move

Remote Control
You can use the remote to control the slider in manual video mode. As well as in auto mode for video, auto loop, time-lapse, and panoramic stills shooting

The slider can traverse the 31″ sliding range in a minimum time of 11.4 seconds to a maximum time of 123 seconds in video mode
In time-lapse, the speed range is 114 seconds to 22 minutes, and 30 seconds at its slowest
The pan and tilt axis each features 360 ? of rotation

Key Features
30" Quiet Motorized Sliding Range
Supports Cameras up to 11 Pounds
Programmable Shooting Modes
Straight, Parallax, or 120° Panning
Height-Adjustable Legs
Three 1/4"-20 & 3/8"-16 Mounting Points
NP-F-Type Battery Lasts About 8 Hours
Ball Joint Head Included
6 x Camera Control Cables Included
The 32" GVM Professional Video Carbon Fiber Motorized Camera Slider features an 11-pound load capacity as well as a 30" slider range along the carbon fiber rails, but that is just the tip of its capabilities. It has an attached controller that enables you to select and control the start/stop positions of the slider along the track, as well as selecting between video and still photo mode. The carbon fiber rail bed features an adjustable channel that allows you to shoot straight (perpendicular to the track rails) in a parabola to keep a subject centered as the camera tracks from side to side, or it can create a 120° panoramic camera move.

The height-adjustable feet are individually adjustable up to 0.79", allowing you to set up the slider on slightly uneven or non-level terrain, while three 1/4"-20 and three 3/8"-16 threaded mounting holes enable tripod mounting. The slider is powered via a removable 4400mAh NP-F-type battery that will run the slider for about eight hours. An included ball joint head mounts on the slider carriage and allows you to orient your camera easily and hold its position as it moves along the track. Six different camera control cables are included, allowing the slider controller to interface with most cameras.

Load Capacity
The slider supports up to 11 pounds when horizontal, and 5.5 pounds when set at a 30° incline.
Programmable Modes
Automatic: Allows you to set the sliding range along the slider as it cycles between the endpoints of the range.
Video capture: Suitable for interviews as the motor is silent.
Delay shooting: Single-frame shooting (time-lapse) with a selectable delay between 1 and 1000.
Orientation
Adjusting the channel between the support rails allows you to adjust the position of your head on the slider as it moves between the ends of the slider track. The channel can be positioned so there is no movement during the slide. You can also set it so the camera shoots in a parabola to keep the subject centered during the move, or it pans the camera up to 120° to create a panoramic shot.
Camera Compatibility
The slider includes six cables that enable the controller to interface with a variety of cameras from Canon, Sony, Nikon, Pentax, GoPro, Fuji, Panasonic, Lycra, Olympus, Samsung, and others.

Key Features
Dual-Handgrip Light with Phone Holder
For Vlogging and Tripod-Mount Setups
Vertical and Horizontal Attachment
Smartphone Photo Trigger on Handgrip
Powered by Included L-Series Battery
5600K Color Temperature with 97 CRI
0 to 99% Dimming
White and Orange Filters Included
2 x Cold Shoe Mounts; 1/4"-20 Threads
Optional DC Adapter Supported
The LT-10S Smartphone Video Camera Rig Light from GVM features a dual-handgrip design and includes an adjustable smartphone holder you can attach in the center. Mount virtually any smartphone in-between the two LED panels, which deliver either warm or cool white light thanks to two sets of filters. An included L-series battery neatly installs on the back and powers the light and a photo trigger on one of the handgrips.

Key Features
Dual Ball Heads
1/4" Connectors at Each End
Supports up to 8.8 lb.
The GVM Aluminum Alloy Adjustable Magic Arm greatly expands your options when using a camera, smartphone, LED light, monitor, microphone, etc. It features 1/4" bolts on each end and 180° rotation for your gear. The Magic Arm supports equipment up to 8.8 pounds.

compact and portable power solution for devices powered by L-series and v mount battery.The included V-mount adapter is a slim V-mount plate that accepts both included 6600mAh NP-F970 batteries or any other L-series batteries. The plate can be mounted on V-mount-powered devices such as cameras and lights to deliver power from L-series batteries. When the plate is used for gear such as certain cameras, two L-series batteries are required to be used because such high-powered devices require more than the 7.2V provided by a singe L-series battery.. The dual charger charges two batteries simultaneously and has an LCD showing the charge status of each battery. Designed with automatic current control, the charger also provides overcharge, over-discharge, over-temperature, overcurrent, overvoltage, and short-circuit protection. The charger is USB-powered and can be connected to a standard USB charger, a computer, or a portable USB power bank, and a USB charging cable is included.

Key Features
For Content Creators and Vloggers
Output: 877 Lux at 3.3' (6400K)
2700 to 10,000K; RGB Control
4 x 9.5"; AC/DC Operation
CRI 97
Onboard and Bluetooth Control
Passive Cooling
0 to 100% Dimming, 8 Lighting Effects
Cold Shoe Mounting
Separately Available AC Adapter
The RGB20W RGB On-Camera LED Light from GVM is a compact on-camera variable color temperature light fixture that features cold shoe mounting and includes a tiltable cold shoe bracket. The light fixture features selectable CCT, HSI, and Scene modes. Featuring 162 LEDs, it has a CCT output from 2700 to 10,000K and a CRI of 97. It can produce the RGB spectrum with 360° and 0 to 100% saturation adjustment.

The CCT mode allows you to select your color temperature output with 0 to 100% stepless dimming, allowing you to use the light in a variety of environments from interior to exterior. HSI mode uses the RGB LEDs to provide you a full spectrum color output, so you can adjust the output from 0 to 360° on the RGB scale while adjusting brightness, as well as saturation from 0 to 100%. Scene mode allows you to access eight built-in special effects. A downloadable app allows you to control your fixture from your phone via Bluetooth. Power the light via the built-in L-series battery plate and included battery or using an optional AC power supply.

Operating Modes
RGB Color Mode
Scroll through the RGB color wheel in 1° increments. Dial-in nearly any color in the visible spectrum.
CCT Mode
The traditional correlated color temperature (CCT) mode allows you to accurately adjust your color temperature from 2700 to 10,000K.
Features
Intuitive On-Unit Interface with OLED Display
The built-in OLED screen offers a simple display, while push buttons and a single rotating knob provide local control of the fixture.
GVM LED App
Install the app on your mobile device to remotely control the fixture via Bluetooth to control color temperature, HSI settings, and brightness, as well as on/off and duration. The app is available for both iOS and Android.
Mounting
The fixture features a 1/4"-20 threaded hole on the bottom and includes a tiltable cold shoe bracket that attaches to the rear of the unit by snapping into slots on the back. This allows you to tilt the fixture forward or back as you desire. The tiltable shoe bracket also has a 1/4"-20 threaded hole for mounting on light stands or other supports.
Accessory
A cold shoe is built into the top of the fixture for mounting accessories on the light.
8 Built-In Scene Modes
Police car, candlelight, TV, bad bulb, lightning, party, disco, paparazzi